How To Repair A Table Lamp

Table lamps are incredibly useful. They provide sufficient light for y'all to perform tasks on a variety of surfaces.

At LampTwist, we know that if yous don't use any tabular array lamps, then I exercise wonder how you can ever cook, read or write in your own abode with condolement. Table lamps are stronger and more direct, and so can help to protect your eyes.

Table lamps are, unfortunately, prone to developing bug over fourth dimension. Most people would simply toss them aside and replace them when this occurs.

It usually isn't actually all that hard to fix a table lamp. The problems typically lie in a single part of the lamp. If you're interested in saving a scrap of money and maintaining your table lamps better, then you're in the correct place.

In this guide,

• Check the Bulb First
• Dismantle Your Lamp
• #ane Remove the Plug from the Wall Socket
• #ii Deal with the Easily Removed Parts First
• #3 Audit Your Socket Beat and Remove It
• #four Pull Out the Socket Switch and Remove the Wires
• #5 Decide the Problem
• #four Pull Out the Socket Switch and Remove the Wires
• Step five – Determine the Problem and Supervene upon Information technology
• Repairing a Damaged Ability Cord
• Recap

Read on to learn how to gear up a tabular array lamp!

Cheque the Bulb First

If you lot haven't checked the bulb yet, do that first! If the seedling is damaged or worn out, then it is incredibly piece of cake to just replace it.

Make sure you remove the table lamp from whatever source of power. Once you've done that, simply unscrew it and insert a brand new light bulb of the same blazon.

If the new seedling lights up when you lot reconnect the power, then problem solved!

However, if it doesn't, that means you accept some other upshot with your lamp. If that is the example, there is simply one thing to do: continue reading!

Dismantle Your Lamp

• Step 1 – Remove the Plug from the Wall Socket
• Step 2 – Bargain with the Easily Removed Parts First
• Pace 3 – Inspect Your Socket Crush and Remove Information technology
• Step 4 – Pull Out the Socket Switch and Remove the Wires
• Step five – Make up one's mind the Problem and Replace Information technology
• Pace iv – Pull Out the Socket Switch and Remove the Wires
• Step v – Make up one's mind the Problem and Replace Information technology

#1 Remove the Plug from the Wall Socket

The start thing that y'all ever need to exercise is to brand sure that your tabular array lamp is completely disconnected from any ability source. Getting electrocuted while trying to ready your tabular array lamp would not exist ideal!

Once you lot've removed the plug from the wall socket, y'all're ready to motility on to the next step.

#two Deal with the Easily Removed Parts Kickoff

The lampshade, lampshade holder or harp and lite seedling are the easiest parts of the lamp to remove. For most tabular array lamps, information technology is as uncomplicated as twisting then removing.

However, if y'all're having trouble removing whatever of these pieces, attempt to find a transmission or ask the manufacturer.

#3 Inspect Your Socket Shell and Remove Information technology

The virtually common socket shells actually have a sticker on them that shows you where to first working to remove them.

Ordinarily, you lot will squeeze a bolt on either side of where the sticker is. Once you've squeezed the bolts, the socket shell should exist loose enough for y'all to slide it upward and off the tabular array lamp.

If this is not what you lot find on your table lamp, do not despair! There are a few different methods, but well-nigh of them are very simple. You may demand to remove a screw or bolt instead, but any it is, it should be adequately clear.

If you practise run into trouble, attempt asking for help from someone who has done it earlier. If you don't know anyone, then you may need to have it to the manufacturer who sold information technology to yous in the offset place.

#4 Pull Out the Socket Switch and Remove the Wires

Before you do anything else, look at the screws holding the socket switch in identify.

• If you notice they are already loose before you've even done anything, then that may have been the problem.
• Tighten the screws and reassemble your table lamp.
• Try plugging it in and see if it works better now.
• If it still doesn't work or the screws were already tight, proceed loosening them and pulling upwardly the socket switch.
• You exercise not need to take the socket switch off – all you take to practice is expose the wiring within information technology.
• Once you tin can encounter the wires, check where each wire is connected.
• There should be ii wires.
• One wire is black and should be connected to a brass screw.
• The other is a white wire that should be continued to a argent spiral.
• Assuming your tabular array lamp was working prior to whatsoever issues, these wires should be correctly attached at this betoken.

Accept note of where the wires are fastened earlier you remove them.

#5 Determine the Problem

Now that you have completely dismantled your table lamp, you can bank check to see which office is damaged. If none of the to a higher place issues turned up, inspect each individual part for any harm.

One time you locate the damaged office, you tin bring it with you to the manufacturer and purchase a new one. Since you lot only had to supplant one part instead of ownership a whole new table lamp, it shouldn't toll yous all that much.

Now that you have a new function, yous tin can but reassemble the table lamp and relish its strong calorie-free one time again!

#4 Pull Out the Socket Switch and Remove the Wires

Before yous do anything else, look at the screws holding the socket switch in place. If you notice they are already loose before you've fifty-fifty done annihilation, then that may have been the problem. Tighten the screws and reassemble your table lamp. Try plugging information technology in and run across if it works better now.

If it however doesn't piece of work or the screws were already tight, continue loosening them and pulling up the socket switch. You lot practice not need to have the socket switch off – all you have to exercise is expose the wiring within it.

One time y'all can run across the wires, check where each wire is connected. There should be 2 wires. One wire is black and should be connected to a brass spiral. The other is a white wire that should exist connected to a silverish spiral.

Assuming your table lamp was working prior to any problems, these wires should exist correctly attached at this point. Take note of where the wires are attached before you remove them.

Step 5 – Determine the Trouble and Supercede It

Now that you have completely dismantled your tabular array lamp, you tin can check to see which part is damaged. If none of the in a higher place bug turned upwardly, inspect each individual part for any damage.

Once you lot locate the damaged office, you can bring it with yous to the manufacturer and purchase a new one. Since you only had to replace i part instead of ownership a whole new table lamp, it shouldn't cost you all that much.

Now that yous have an extra part, you can just reassemble the table lamp and relish its potent calorie-free once more!

Repairing a Damaged Power Cord

If the wiring in your power string is causing the problem, y'all may not even need to replace the whole thing. If you can see the damaged portion of the wire, you can simply cut that portion off.

One time you've done so, you lot volition need to remove nearly an inch of the cord's protective covering so that the ends of the wires are exposed again.

Now, all yous need to do is reattach the wires to the socket switch and you have a fully functional power cord again.

If you were still unable to set up your table lamp later on following all of these tips and instructions, you volition definitely want to bring it to a professional and have it checked out.

Even if you weren't able to repair it yourself, at that place is notwithstanding a take a chance that a professional can fix it.

Epitomize

If worse comes to worst and the table lamp is beyond repair, at least y'all tried your best to relieve it. Now y'all can replace your table lamp knowing that you did everything in your power to set up the quondam ane! If are in need of a replacement, explore our living room lighting to view our selection of lighting for your living room.

Source: https://lamptwist.com/blog/repair-faulty-desk-lamp/

Share this post